Effect of gamma sterilization on the properties of microneedle array transdermal patch system.

Soluble microneedles (MNs) of four different hydrophilic polymers namely sodium carboxymethyl cellulose (CMC), polyvinylpyrrolidone (PVP) K30, PVP K90 and sodium hyaluronate (HU) were fabricated by mold casting technique. When exposed to gamma radiation, a dose of 25 kilogray (kGy) was found to render the microneedle (MN) sterile. However, CMC was found to form MNs with poor mechanical properties, whereas PVP K30 MNs were drastically deformed upon exposure to applied dose as observed in bright field microscopy. Scanning electron microscopy (SEM) revealed that morphology of PVP K90 and HU MNs were not significantly affected at the applied dose. The appearances of characteristic peaks of irradiated MNs of PVP K90 and HU in Fourier-transform infrared spectra suggested structural integrity of the polymers on irradiation. Differential scanning calorimetry (DSC) indicated gamma irradiation failed to alter the glass transition temperature and thus mechanical properties of PVP K90 MNs. However, DSC and Powder X-ray Diffraction (PXRD) conclusively indicated that the degree in crystallinity of HU was substantially reduced on irradiation. In vitro dissolution profiles of sterile PVP K90 and HU MNs were similar to un-irradiated MNs with a similarity factor (f2) of 64 and 54, respectively. In vivo dissolution studies in human subjects indicated that sterile MNs of PVP K90 and HU exhibited dissolution of 78.45 ± 1.09 and 78.57 ± 0.70%, respectively, after 20 min. The studies suggested that PVP K90 and HU could be suitable polymers to fabricate soluble MNs as the structural, morphological, microstructural and dissolution properties remained unaltered post γ sterilization.

Radiotracer investigation in a pilot-scale fluidized bed coal gasifier (FBCG).

Radiotracer investigations were carried out for measurement and analysis of residence time distribution (RTD) of coal particles in a pilot-scale gasifier fitted with a flat air/steam distributor. Measurements were made at different operating conditions using gold-198 (198Au) labeled coal particles as a radiotracer. The measured RTDs were treated and mean residence times (MRTs) were determined. Furthermore, the treated RTDs were simulated using a suitably conceptualized mathematical model and detailed information about hydrodynamics of coal particles within the gasifier was obtained. Results of model simulation indicated that the gasifier behaved as an ideal mixer of fine coal particles exiting from the top of the gasifier. A small fraction of the coarser particles was found to be bypassing at ambient temperature.

Decomposition of antibiotic ornidazole by gamma irradiation in aqueous solution: kinetics and its removal mechanism.

An efficient gamma radiolytic decomposition of one of the extensively used pharmaceutical ornidazole (ORZ) was explored under different experimental conditions by varying initial concentrations, solution pHs, and doses and concentrations of inorganic ([Formula: see text]) and organic (t-BuOH) additives. The results showed that low ORZ concentrations could be efficiently decomposed using gamma irradiation. The decomposition was followed by pseudo first-order reaction kinetics with rate constant values of 2.34, 1.48, 1.11, and 0.80 kGy-1 for the following initial concentrations: 25, 50, 75, and 100 mg L-1 with their corresponding (G(-ORZ)) values of 1.004, 1.683, 2.237, and 2.273, respectively. Decomposition rate of ORZ was remarkably improved under acidic condition when compared to neutral or alkaline medium. It was also observed that the decomposition was primarily caused by the reaction of ORZ with radiolytically generated reactive HO• radicals. The addition of H2O2 had a synergistic effect on the decomposition and mineralization extent of ORZ. However, the removal of total organic carbon (TOC) was not as effective as the decomposition of ORZ. Finally, the quantum chemical calculations were employed to optimize the geometry structure of ORZ and liquid chromatography quadrupole time-of-flight mass spectrometry (LC-QTOF-MS) was used to identify the decomposition intermediates. On the basis of Gaussian calculations and analysis of LC-QTOF-MS, it can be inferred that ORZ radiolytic decomposition was mainly attributed to oxidative HO• radicals and the direct cleavage of ORZ molecules. Possible pathways for ORZ decomposition using gamma irradiation in aqueous medium were proposed.

Assessment of reaction intermediates of gamma radiation-induced degradation of ofloxacin in aqueous solution.

Gamma radiolytic degradation of an antibiotic, ofloxacin (OFX) was investigated under different experimental conditions. The parameters such as initial OFX concentration, solution pH, absorbed dose and the concentrations of inorganic (CO32-) and organic (t-BuOH) additives were optimized to achieve the efficient degradation of OFX. The degradation dose constant values of OFX were calculated as 2.364, 1.159, 0.776 and 0.618 kGy-1 for the initial OFX concentrations of 0.05, 0.1, 0.15 and 0.2 mM with their corresponding (G (-OFX)) values of 0.481, 0.684, 1.755 and 1.971, respectively. Degradation rate of OFX was significantly increased with increase in the absorbed dose and decrease in the initial OFX concentration under acidic condition when compared to neutral or alkaline condition. Reaction of OFX in the presence of CO32- and t-BuOH showed that the degradation was primarily caused by the reaction of OFX with radiolytically generated reactive hydroxyl radicals. Mineralization extent of OFX was determined in terms of percentage reduction in total organic carbon (TOC) and results revealed that the addition of H2O2 enhanced the mineralization of OFX from 29% to 36.1% with H2O2 dose of 0.5 mM at an absorbed dose of 3.0 kGy. Based on the LC-QTOF-MS analysis, gamma radiolytic degradation intermediates/products of OFX were identified and the possible degradation pathways of OFX were proposed. Cytotoxicity study of the irradiated OFX solutions showed that gamma radiation has potential to detoxify OFX.

Mitigation of Cr(VI) toxicity using Pd-nanoparticles immobilized catalytic reactor (Pd-NICaR) fabricated via plasma and gamma radiation.

Catalytic reduction of Cr(VI) to less toxic Cr(III) form using metal nanoparticles is one of the novel approaches adopted to deal with Cr toxicity. In this work, we report the fabrication of a facile, reusable, and robust Pd nanoparticles-immobilized catalytic reactor (Pd-NICaR) system using green, environment-friendly gamma radiolytic, and plasma polymerization processes. A room temperature, RF-powered plasma polymerization process was employed to functionalize a polyethylene-polypropylene (PE-PP) non-woven matrix with epoxy group containing monomer 2,3-epoxypropyl methacrylate (EPMA). EPMA-functionalized PE-PP (EPMA-f-PE-PP) substrate was subsequently used as a template for in situ generation and immobilization of Pd NPs via gamma radiolytic route. The samples were characterized using FTIR, SEM, XPS, and XRF techniques. The catalytic efficacy of Pd-NICaR towards Cr(VI) reduction, in the presence of formic acid (FA) as a reductant, was investigated spectrophotometrically, and reaction parameters were optimized at reaction temperature of 50 °C and [FA]/[Cr(VI)] = 680 to achieve catalytic reduction efficiency of 99.7% within 10 min in batch process. The system showed excellent reusability (~ 20 cycles) and storage stability (> 30 days) without substantial loss (~ 11%) of activity. Practical applicability of the robust catalytic system towards Cr(VI) toxicity mitigation was established in continuous flow mode using a fixed-bed column reactor.

Radiation grafting: A voyage from bio-waste corn husk to an efficient thermostable adsorbent.

The initiator free environmentally benign gamma radiation is employed to graft poly-acrylic acid (PAA) onto the widely produced bio-waste corn husk to develop promising, cheap, efficient and reusable adsorbent (AAc-g-husk) having specific adsorption capacity of 1682.7mgg-1 of methylene blue (MB) at pH 9.0 and 320K. The most suitable grafting yield is found by optimizing absorbed dose, dose rate and concentrations of monomer, Mohr's salt and inorganic acid. The inter-planar hydrogen bonding among (002) planes of cellulose in the husk decreases after diversifying grafting of PAA on ad-axial, ribs and micro-fibrils surfaces of the corn husks. The chemically and structurally modified AAc-g-husk shows superior thermal stability. The mechanism of MB dye adsorption by AAc-g-husk has been discussed through six two-parameters adsorption isotherm and ten three-parameters adsorption isotherm models at three different temperatures (300, 310 and 320K), seven kinetic models at room temperature, FT-IR and desorption studies in different solvent compositions.

Structural re-arrangement of depolymerized sodium alginate enriches peltate glandular trichomes and essential oil production of spearmint.

Over the past decade, radiation-degraded polysaccharides have been used as regulators of growth and development in several crop plants. In quest of the possible reasons of previously established growth-promotion activity of irradiated sodium alginate (ISA), structural parameters of irradiated and un-irradiated sodium alginate were analysed using Ultraviolet-visible spectroscopy (UV-vis) and Fourier Transform Infrared spectroscopic (FT-IR) studies to develop an understanding of structure-property relationship. Using foliar application, response to graded concentrations of ISA was tested in terms of yield and quality attributes of spearmint (Mentha spicata L.). Among different concentrations of ISA [0 (control), 40, 80, 120 and 160mgL-1], 80mgL-1 proved to be the optimum foliar-spray treatment for most of the parameters studied including peltate glandular-trichomes density, which was increased from 20 to 44mm-2. Measurements made at 150days after planting revealed that foliar application of ISA at 80mgL-1 increased the content and yield of spearmint essential oil (EO) by 36.0 and 122.6%, respectively, in comparison to the control. Compared to the control, gas chromatography mass spectrometry (GC-MS) analysis revealed an increase of 18.7% in the carvone content and a decrease of 15.7% in limonene content of the spearmint EO.

Mineralization and biodegradability enhancement of Methyl Orange dye by an effective advanced oxidation process.

An effective process for the oxidation of Methyl Orange dye (MO) was determined by comparing the mineralization efficiency between two advanced oxidation processes (AOPs) viz., ozonolysis and gamma radiolysis in presence and absence of an added inorganic salt potassium persulfate (K2S2O8). The effects of various operating parameters such as ozone flow rate and reaction temperature were optimized to achieve the best possible mineralization extent of MO by ozonolysis. The mineralization efficiency of MO was significantly enhanced during gamma radiolysis in presence of K2S2O8 (γ+K2S2O8) compared to in absence of K2S2O8. The presence of methyl group at the amine of phenyl ring assisted the mineralization of dye during γ+K2S2O8. The oxygen-equivalent chemical-oxidation capacities (OCC) of ozonolysis and γ+K2S2O8 for 75% mineralization of the dye solution were calculated as 7.008 and 0.0336kg equiv. O2 m-3, respectively which signifies that γ+K2S2O8 can be explored as an effective AOP. The non-biodegradable MO dye solution became biodegradable even after the dose of 0.5 kGy during γ+K2S2O8 compared to 1 kGy in absence of K2S2O8. The study concludes that a lower dose γ+K2S2O8 could be one of the efficient pretreatment steps before undergoing biological degradation of dye solution.

Study of adsorption characteristics of Au(III) onto coal particles and their application as radiotracer in a coal gasifier.

This paper describes a systematic study carried out to investigate adsorption characteristics of 198Au onto the surface of coal particles using a radiotracer technique. The main objective of the study was to optimize labeling conditions and utilize the labeled coal particles as a radiotracer for tracing coal particles in fluidized bed coal gasifiers. The effect of various experimental factors such as pH, amount of adsorbent, initial gold concentration, temperature and contact time between adsorbate and adsorbent were studied to obtain optimum conditions for maximum adsorption of 198Au on coal particles from an aqueous solution. Analysis of the data showed that the Langmuir model was found most suitable to describe the adsorption phenomena. The thermodynamic analysis showed that the adsorption process is feasible, spontaneous and endothermic in nature. The results of the kinetics suggested that the adsorption presumably follows second order kinetics and chemisorption in nature. Based on the optimized conditions, the amount of coal particles and activity to be used for tracing the coal phase in pilot-scale gasifiers was estimated. Accordingly, the radiotracer was prepared and successfully used for measurement of residence time distribution (RTD) in a pilot-scale coal gasifier.

Efficient degradation of butylparaben by gamma radiolysis.

Gamma radiolysis and ozonolysis are two competitive advanced oxidation processes for degradation of organic pollutants present in the ground water. In this paper, the gamma radiolytic degradation of an emerging organic pollutant Butylparaben (BP) in aqueous solution has been investigated for the first time at different absorbed doses. The effect of the absorbed dose rate in the degradation and mineralization of BP has been investigated. About 65% mineralization of BP was observed at absorbed dose of 70kGy and dose rate of 0.7kGyh-1. Interestingly, turbidity appeared in the solution during radiolysis at doses higher than 2kGy, which disappeared again at very higher dose (~90kGy) making the solution again transparent. At lower dose rate of 0.175kGyh-1 the turbidity was appeared at much lower dose about 1kGy. However, the dose rate showed no effect in the dose of the disappearance of the turbidity. The hydrophobic fragments insoluble in water were generated during the initial stage of gamma radiolysis and those were completely mineralized to CO2 and H2O by direct absorption of gamma radiation. About 90kGy dose was required to achieve ~90% mineralization of BP. On the contrary, maximum 50% mineralization was achieved after 5h of ozonation at the O3 flow rate of 0.5Lmin-1 at pH 7.5 and it remained even constant upon prolonged ozonation. The oxygen-equivalent-chemical-oxidation-capacity (OCC) was used as the parameter to compare the % mineralization efficiencies of the two oxidative processes studied here and the gamma radiolysis was found to be more efficient between those processes. The phytotoxicity of the treated BP solution to agricultural seeds showed that the radiolytically generated fragments were less toxic compared to ozonolytically generated fragments. Thus gamma radiolysis is effective for reducing the organic burden and the toxicity of water polluted with emerging pollutants like BP.

Designing tragacanth gum based sterile hydrogel by radiation method for use in drug delivery and wound dressing applications.

Present article discusses synthesis and characterization of the sterile and pure hydrogel wound dressings which were prepared through radiation method by using polyvinyl alcohol (PVA), tragacanth gum (TG) and sodium alginate (SA). The polymer films were characterized by SEM, Cryo-SEM, FTIR, solid state C(13) NMR and XRD, TGA, and DSC. Some important biological properties such as O2 permeability, water vapor transmission rate, microbial permeability, haemolysis, thrombogenic behavior, antioxidant activity, bio-adhesion and mechanical properties were also studied. The hydrogel film showed thrombogenicity (82.43±1.54%), haemolysis (0.83±0.09%), oxygen permeability (6.433±0.058mg/L) and water vapor permeability (197.39±25.34g/m(2)/day). Hydrogel films were found biocompatible and impermeable to microbes. The release of antibiotic drug moxifloxacin occurred through non-Fickian mechanism and release profile was best fitted in Hixson-Crowell model for drug release. Overall, these results indicate the suitability of these hydrogels in wound dressing applications.

Cellulose based cationic adsorbent fabricated via radiation grafting process for treatment of dyes waste water.

A cationized adsorbent was prepared from cellulosic cotton fabric waste via a single step-green-radiation grafting process using gamma radiation source, wherein poly[2-(methacryloyloxy) ethyl]trimethylammonium chloride (PMAETC) was covalently attached to cotton cellulose substrate. Radiation grafted (PMAETC-g-cellulose) adsorbent was investigated for removal of acid dyes from aqueous solutions using two model dyes: Acid Blue 25 (AB25) and Acid Blue 74 (AB74). The equilibrium adsorption data was analyzed by Langmuir and Freundlich isotherms, whereas kinetic data was analyzed by pseudo first order, pseudo second order, intra particle diffusion and Boyd's models. The PMAETC-g-cellulose adsorbent with 25% grafting yield exhibited equilibrium adsorption capacities of ∼ 540.0mg/g and ∼ 340.0mg/g for AB25 and AB74, respectively. Linear and nonlinear fitting of adsorption data suggested that the equilibrium adsorption process followed Langmuir adsorption isotherm model, whereas, the kinetic adsorption process followed pseudo-second order model. The multi-linearities observed in the intra-particle kinetic plots suggested that the intraparticle diffusion was not the only rate-controlling process in the adsorption of acid dyes on the adsorbent, which was further supported by Boyd's model. The adsorbent could be regenerated by eluting the adsorbed dye from the adsorbent and could be repeatedly used.

Dysprosium sorption by polymeric composite bead: robust parametric optimization using Taguchi method.

Polyethersulfone-based beads encapsulating di-2-ethylhexyl phosphoric acid have been synthesized and evaluated for the recovery of rare earth values from the aqueous media. Percentage recovery and the sorption behavior of Dy(III) have been investigated under wide range of experimental parameters using these beads. Taguchi method utilizing L-18 orthogonal array has been adopted to identify the most influential process parameters responsible for higher degree of recovery with enhanced sorption of Dy(III) from chloride medium. Analysis of variance indicated that the feed concentration of Dy(III) is the most influential factor for equilibrium sorption capacity, whereas aqueous phase acidity influences the percentage recovery most. The presence of polyvinyl alcohol and multiwalled carbon nanotube modified the internal structure of the composite beads and resulted in uniform distribution of organic extractant inside polymeric matrix. The experiment performed under optimum process conditions as predicted by Taguchi method resulted in enhanced Dy(III) recovery and sorption capacity by polymeric beads with minimum standard deviation.

Radiolytically depolymerized sodium alginate improves physiological activities, yield attributes and composition of essential oil of Eucalyptus citriodora Hook.

Eucalyptus citriodora Hook. is highly valued for its citronellal-rich essential oil (EO) extracted from its leaves. Hence, escalated EO production of eucalyptus is the need of hour. Marine polysaccharides (sodium alginate) are processed through gamma radiation of particular intensity, to obtain the irradiated sodium alginate (ISA). A pot experiment was conducted to study the effect of foliar application of ISA on growth, biochemical, physiological, EO yield and composition of E. citriodora. The treatments were applied as: foliar spray of deionized water only (control), seed soaked with ISA (90 mg L(-1)) and foliar spray of ISA with 30, 60, 120 and 240 mg L(-1). The treatment 6 (spray of ISA at 120 mg L(-1)) showed the highest value for most of the parameters studied. It also enhanced the EO content (33.3%), EO yield (86.7%), citronellal content (63.4%) and citronellal yield (205.5%) as compared to the control.

Design of sterile mucoadhesive hydrogels for use in drug delivery: effect of radiation on network structure.

Radiation induced graft copolymerization is pure, sterile and additive free method for the synthesis of hydrogels for biomedical applications. In the present work, attempt has been made to prepare the biocompatible, mucoadhesive hydrogels based on natural polysaccharide sterculia gum and polyvinylpyrrolidone (PVP) for use as drug delivery devices. The effect of gamma radiation on swelling and various network parameters of hydrogels such as the polymer volume fraction in the swollen state (ϕ), molecular weight of the polymer chain between two neighboring cross links (M¯c), crosslink density (ρ), and mesh size (ξ) have been studied. Hydrogels have been characterized with scanning electron micrographs (SEMs), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction study (XRD), thermo gravimetric analysis (TGA) and swelling studies. Swelling and mesh size decreased while gel strength and crosslink density increased with increase in radiation dose. The swelling of hydrogels and release of drug ciprofloxacin from drug loaded hydrogels occurred through non-Fickian diffusion mechanism. These hydrogels have been observed to have non-thrombogenic, haemo-compatible and mucoadhesive nature and could be used as mucoadhesive drug delivery system to deliver drug to gastro intestinal tract (GIT) in controlled manner.

Effect of irradiated sodium alginate and phosphorus on biomass and artemisinin production in Artemisia annua.

It is now being realized that irradiation products of natural bioactive agents can also be beneficially utilized to impart value addition in agriculture by converting these bioactive agents into more useful form. Polysaccharides, such as sodium alginate, have proven to be wonderful growth promoting substances in their depolymerized form for various plants. Artemisinin has been increasingly popular as an effective and safe alternative therapy against malaria; also proved effective against the highly adaptable malaria parasite, which has already become resistant to many other drugs. The drug artemisinin can be extracted from the leafy tissues of Artemisia annua. Therefore, experiments were conducted with an aim to evaluate artemisinin production and overall plant development though depolymerized sodium alginate application and nutrient supply. In the present study, sodium alginate, irradiated by Co-60 gamma rays together with various phosphorus doses, was used to study their effect on growth, physiological and biochemical processes and production of artemisinin in A. annua. Among various applied doses of phosphorus fertilizer, P40 (40 kg Pha(-1)) together with ISA80 (80 mg L(-1)) significantly improved all the parameters studied. Increase in plant height as well as weight was noted at this treatment. Dry leaf yield, artemisinin concentration in leaves and artemisinin yield was also significantly enhanced by the treatment.

Studies on production of fructo-oligosaccharides (FOS) by gamma radiation processing of microbial levan.

Microbial levan, a natural polymer of fructose, was produced and purified by alcohol precipitation from culture supernatants of Bacillus megaterium type 1 grown in an optimized liquid sucrose medium. GPC analysis showed that the yield of the major fraction of levan having molecular weight ~5000 D increased with increase in sucrose concentration in the broth. Levan subjected to (60)Co-gamma radiation as well as acid hydrolysis was investigated by rheometry, UV-visible spectrophotometry and gel permeation chromatography (GPC) techniques. Unlike most of the polysaccharides, levan powder exhibited good radiation degradation stability up to 150 kGy. Gamma irradiation of 10% levan aqueous solution at 250 kGy yielded 63.0% fructo-oligosaccharide (FOS) with an average molecular weight of 1250 D. Acid hydrolysis of levan using 0.5 N HCl for 60 min treatment time gave rise to the desired FOS with lower yield (23.1%) as compared to that obtained in gamma radiolysis process.

An insight into the influence of low dose irradiation pretreatment on the microbial decolouration and degradation of Reactive Red-120 dye.

The influence of low dose irradiation pretreatment on the microbial decolouration and degradation of Reactive Red-120 (RR-120) dye was investigated in detail by using Pseudomonas sp. SUK1. About 27%, 56% and 66% decolouration of 150 ppm RR-120 dye solution was observed by applying 0, 0.5 and 1 kGy doses, respectively, in the first step followed by microbial treatment for 24 h under static condition. Similarly, about 70%, 88% and 90% TOC removal was observed by applying 0, 0.5 and 1 kGy doses, respectively, in the first step followed by the microbial treatment for 96 h under static condition. The radiation induced fragmented products of RR-120 at doses of 0.5 and 1 kGy were investigated by FTIR and electrospray ionization-MS analysis. The induction of the enzymes viz. laccase, tyrosinase, azoreductase and NADH-2,6-dichlorophenol indophenol reductase was studied in the decolourised solution obtained after irradiating 150 ppm RR-120 dye solution with 0 and 1 kGy doses followed by the microbial treatment for 96 h under static condition. The enzymatic degradation products were studied by FTIR, HPLC and GC-MS. The toxicity study of the treated dye solution on plants revealed the degradation of RR-120 into non-toxic products by combined radiation-microbial treatment. This study explores a reliable and promising way to use industrially viable dose (≤1 kGy) and microbial strain viz. Pseudomonas sp. SUK1 for permissible safe disposal of dye solutions from textile industries.

Depolymerized carrageenan ameliorates growth, physiological attributes, essential oil yield and active constituents of Foeniculum vulgare Mill.

Irradiated carrageenan (IC) elicits an array of plant defense responses and biological activities in plants. An experiment was carried out in the naturally illuminated conditions of net house in order to assess the effects of foliar spray of IC on agricultural performance of fennel (Foeniculum vulgare Mill.), which is a high-value essential oil bearing medicinal crop used in pharmaceutical, food and cosmetic industries. There were applied four IC concentrations (40, 60, 80 and 100 mg L(-1)) as foliar sprays. Application of IC significantly improved the growth attributes, physiological and biochemical parameters, essential oil yield and the contents of main components of essential oil of fennel. IC applied at 80 mg L(-1) enhanced these parameters maximally. Unirradiated carrageenan and deionized water had no effect on the attributes studied. Moreover, GLC analysis revealed a significant increase in the components of essential oil, viz. fenchone (4.48-7.82%) and anethole (78.38-86.08%) compared to the control.